⌖WEAPONTESTER
Ballistics Fundamentals

Altitude, Temperature,
Pressure, and Humidity

Last updated: · 9 min read

Every atmospheric variable a shooter worries about, altitude, temperature, barometric pressure, and humidity, changes bullet drop through a single mechanism: air density. Less dense air means less drag, which means a flatter trajectory and a smaller scope correction. More dense air does the opposite. Once you know the density, the four input variables are interchangeable; that is why ballistic computers and military fire-control systems collapse them into a single number calleddensity altitude.

The only variable that actually moves the bullet

Aerodynamic drag on a projectile is proportional to the air density it is flying through:

F_drag = ½ · ρ · v² · Cd · A

ρ (rho) is air density in kg/m³. Cut ρ in half and you cut drag in half at the same velocity. Temperature, pressure, humidity, and altitude do not appear directly in the equation of motion. They only appear through ρ. This is why two completely different sets of weather conditions can produce the same trajectory, and why a single density-altitude reading captures everything the bullet cares about.

Air density itself comes from the ideal gas law:

ρ = (P − Pv) / (Rd · T) + Pv / (Rv · T)

where P is station pressure, Pv is the partial pressure of water vapor (humidity × saturation pressure at the current temperature), T is absolute temperature, and Rd / Rv are the specific gas constants for dry air and water vapor. Altitude does not appear directly; it acts only by reducing station pressure as you climb.

The ICAO standard atmosphere baseline

Every published drop table, every advertised BC, and every default condition in a ballistics calculator references the same baseline: the ICAO standard atmosphere defined by ICAO Doc 7488/3 (and the equivalent U.S. Standard Atmosphere, 1976). At sea level:

When a manufacturer prints "at standard conditions," this is what they mean. Every chart in this article uses ICAO standard atmosphere as the reference unless stated otherwise. The WeaponTester engine derives station pressure from altitude via the standard tropospheric pressure model and computes ρ via the equation above using the Arden Buck (1996) saturation vapor pressure formula for the humidity term.

Altitude: same load, sea level vs 5,000 feet

All numbers below were computed by the WeaponTester ballistics engine, which is validated against JBM Ballistics to within ~5% on drop and drift for benchmark loads. Both loads are zeroed at 100 yards with a 1.5 inch sight height. Atmospheres are ICAO-standard at the stated altitude: 59 °F / 29.92 inHg at sea level, 41 °F / 24.90 inHg at 5,000 feet.

LoadRangeSea level5,000 ftΔ MOA
.308 168gr SMK · 2650 fps500 yd64.3 in / 12.28 MOA60.5 in / 11.55 MOA−0.73
.308 168gr SMK · 2650 fps1000 yd455.6 in / 43.50 MOA396.1 in / 37.82 MOA−5.68
6.5 CM 140gr ELD-M · 2710 fps500 yd53.7 in / 10.26 MOA51.6 in / 9.86 MOA−0.40
6.5 CM 140gr ELD-M · 2710 fps1000 yd325.6 in / 31.10 MOA300.3 in / 28.68 MOA−2.42

Computed by the WeaponTester engine; ICAO standard atmospheres at stated altitudes; G7 BCs used (.308 168gr SMK = 0.218, 6.5 CM 140gr ELD-M = 0.315, both Litz-measured Doppler values).

The .308 picks up almost 5 MOA of drop relief at 1000 yards by moving from a sea-level range to a 5,000-foot mountain range. The 6.5 CM picks up about 2.4 MOA, less because the higher-BC bullet was already losing less velocity to drag. Both numbers are big enough that dialing a sea-level zero at altitude will land you well over the steel.

Temperature: same load, 30 °F vs 90 °F

Holding station pressure constant at ICAO 29.92 inHg and humidity at zero, only the temperature term in ρ changes. This isolates the air-density effect from the powder-temperature effect (which the engine does not model; see caveat below).

LoadRange30 °F90 °FΔ MOA
.308 168gr SMK · 2650 fps500 yd65.6 in / 12.52 MOA63.1 in / 12.05 MOA−0.47
.308 168gr SMK · 2650 fps1000 yd476.8 in / 45.53 MOA436.4 in / 41.67 MOA−3.86
6.5 CM 140gr ELD-M · 2710 fps500 yd54.4 in / 10.39 MOA53.1 in / 10.13 MOA−0.26
6.5 CM 140gr ELD-M · 2710 fps1000 yd334.3 in / 31.92 MOA317.6 in / 30.33 MOA−1.59

Sea-level station pressure 29.92 inHg, 0% RH, ICAO. Drag effect only; does not include muzzle-velocity change from powder temperature.

Powder-temperature caveat. Most modern propellants gain roughly 1–2 fps of muzzle velocity per °F as the powder warms (varies sharply by powder type; "temperature-stable" extruded powders like Hodgdon Extreme can be under 0.5 fps/°F, while older ball powders can exceed 2 fps/°F). A 60 °F swing can therefore move muzzle velocity by 30–120 fps in addition to the drag-only numbers above. That effect is load-specific and outside the drag model; chronograph your load at the temperature you intend to shoot.

Density altitude: the unifier

Because every atmospheric variable acts through ρ, you can collapse temperature, pressure, humidity, and altitude into a single number called density altitude, the altitude in the ICAO standard atmosphere that has the same density as your current conditions. A hot day at low elevation can have a density altitude in the thousands of feet; a cold morning at altitude can have a negative density altitude. Two completely different weather conditions with the same density altitude shoot identically.

The chart below plots .308 168gr SMK drop at 1000 yards (MOA, 100 yd zero) across five atmospheres at four density altitudes. The relationship is essentially linear, which is what makes density altitude such a useful single-number proxy. The size of that effect varies with the cartridge; compare .308 Win and 6.5 Creedmoor at distance for a side-by-side trajectory analysis.

Air density also changes the stability margin of a bullet in a given barrel. See thebarrel twist and bullet stability guide for how altitude and temperature affect the Miller stability factor.

.308 168gr SMK · 1000 yd drop (MOA) vs density altitude
3538414447-2k02.5k5k7.5k45.5 (30°F SL)43.5 (ICAO SL)41.7 (90°F SL)37.8 (5000 ft ICAO)36.3 (5000 ft, 75°F)Density altitude (ft)1000 yd drop (MOA)

Five different atmospheres, one trend line. Density altitude collapses temperature, pressure, and humidity into a single number that predicts drop.

Does humidity actually matter?

Yes, but barely. Water vapor (molecular weight 18) is lighter than the dry air it displaces (mean molecular weight 29), so humid air is less dense than dry air at the same temperature and pressure. Going from 0% to 100% relative humidity at 75 °F and sea level drops ρ from about 1.188 kg/m³ to 1.175 kg/m³, roughly 1.1%.

On a .308 168gr at 1000 yards, that 1.1% density change moves drop from 42.52 MOA (dry) to 42.07 MOA (saturated), a difference of 0.45 MOA, or about 4.7 inches at 1000 yards. That is smaller than the spread between two well-loaded chronograph shots, smaller than typical shooter group error, and well inside the engine's ±5% validation band against JBM. For field shooting at any reasonable range, you can ignore humidity. Temperature and altitude are where the real money lives.

Counter-intuition check: humid air is less dense than dry air, even though it "feels heavier." That intuition is doing thermoregulation math, not gas-law math.

Practical: home range to mountain trip

Concrete workflow when leaving a familiar range to shoot under different atmosphere:

  1. Look up (or measure with a Kestrel / pocket weather meter) the new station pressure, temperature, and humidity at the firing point. Station pressure, not the altimeter setting you hear on a weather forecast.
  2. Compute density altitude. The WeaponTester engine surfaces it in/range; any Kestrel 5700 will display it natively.
  3. Re-run your drop table at the new density altitude. Do not just shift the muzzle velocity and hope.
  4. Confirm with a true at the longest practical distance before relying on the calculated dope. A 100-yard zero remains a 100-yard zero across reasonable atmospheric swings; the deltas you saw above all open up past about 400 yards.

Two rules of thumb for back-of-Kestrel mental math on a .308-class load:

Both rules degrade as you push past 1200 yards (the bullet enters the transonic regime where the drag curve gets nonlinear), and both should be treated as planning aids, not as replacements for a real solver.

Setting atmosphere in the WeaponTester range

The/rangepanel exposes the four input variables directly: temperature (°F), station pressure (inHg), relative humidity (%), and altitude (ft). The engine computes ρ via the equation above, derives the speed of sound from temperature only (ICAO convention), and reports density altitude back to you as a sanity check.

If you only know your sea-level / altimeter pressure, set altitude to 0 and enter the altimeter reading. If you know your true station pressure (from a Kestrel or panel barometer), set altitude to your actual elevation and use the station value. The engine uses the pressure you give it and uses altitude only for the density-altitude display.

Frequently asked questions

Does altitude affect how far a bullet drops?

Yes. Higher altitude means lower air density, which means less drag, which means a flatter trajectory. A .308 Win 168gr load that drops about 456 inches at 1000 yards at sea level under ICAO standard conditions drops about 396 inches at 5,000 feet under standard conditions, a difference of roughly 5.7 MOA. The mechanism is air density, not altitude directly.

How much does temperature affect bullet velocity and drop?

Two distinct effects. First, warmer air is less dense: going from 30 °F to 90 °F at constant pressure removes about 3.9 MOA of drop at 1000 yards on a .308 Win 168gr load. Second, warmer powder burns faster, raising muzzle velocity by roughly 1–2 fps per °F for most propellants. The powder-temperature effect is load-specific and depends heavily on the propellant used (Hodgdon Extreme powders are far more stable than older ball powders).

Does humidity affect bullet trajectory?

Slightly. Water vapor is lighter than the dry air it displaces, so humid air is less dense. Going from 0% to 100% relative humidity at 75 °F and sea level moves 1000-yard drop on a .308 by under half an MOA, about 4.7 inches. Practically irrelevant for field shooting. The "humid air is heavier" intuition is wrong.

What is the ICAO standard atmosphere in ballistics?

The ICAO standard atmosphere (ICAO Doc 7488/3, mirrored by the U.S. Standard Atmosphere 1976) is the reference condition used by virtually every ballistics calculator and BC measurement. Sea-level values: 59 °F, 29.92 inHg, density 1.225 kg/m³, speed of sound 1116 fps. Manufacturer drop tables and published BCs are referenced to this atmosphere unless stated otherwise.

What is "density altitude" and why do shooters use it?

Density altitude is the altitude in the ICAO standard atmosphere that has the same density as your actual conditions. It collapses temperature, pressure, and humidity into a single number that predicts trajectory. A cool day at 5,000 ft and a hot day at 2,000 ft can have the same density altitude and shoot identically. Kestrel meters, ballistic computers, and the WeaponTester range all display it.

Sources

  1. ICAO. Manual of the ICAO Standard Atmosphere, Doc 7488/3, 3rd ed., 1993. Defines the standard temperature, pressure, density, and lapse-rate profile used as the reference atmosphere by virtually every ballistic calculator.
  2. NASA / NOAA / USAF. U.S. Standard Atmosphere, 1976 (NASA-TM-X-74335). The equivalent U.S. reference model.
  3. Litz, B. Applied Ballistics for Long Range Shooting, 3rd ed., Applied Ballistics LLC, 2015. Chapter on atmospheric corrections and density altitude is the standard civilian reference.
  4. Buck, A.L. "New equations for computing vapor pressure and enhancement factor."J. Appl. Meteor. 20, 1981 (with 1996 revision). Saturation vapor pressure equation used for the humidity term in air density.
  5. JBM Ballistics. Trajectory Calculator. jbmballistics.com. Industry-standard validation reference for the WeaponTester engine.
  6. Taylor, M. and Grubbs, F. "Approximate Probability Distributions for the Extreme Spread."Frankford Arsenal Report. Supporting reference for propellant temperature sensitivity figures.
Try it yourself

Set your atmosphere in the range

Pick a load, dial in temperature, pressure, humidity, and altitude, and watch the trajectory and density altitude update live. Compare a sea-level cold morning against a mountain afternoon and see exactly how many MOA you'd burn by forgetting to update your dope.

Set your atmosphere in the range →

Range essentials · Amazon affiliate links

Plan beyond the simulation

Compare personal protection and note-taking supplies for your next range visit.

Hearing protection

Compare earmuffs and earplugs by fit, comfort, and the manufacturer’s published protection rating.

Compare hearing protection on Amazon →

Eye protection

Compare safety glasses by coverage, lens tint, and documented impact rating.

Compare safety glasses on Amazon →

Keep your observations together

A weather-resistant notebook gives your session notes and conditions a home away from the screen.

Browse field notebooks on Amazon →

As an Amazon Associate, we earn from qualifying purchases. Links open Amazon search results; compare the current listings and specifications there. Affiliate disclosure