Wind drift at distance
Published: · 7 min read
A wind call has three inputs: the wind's crossrange component, the bullet's drag history, and the distance to the target. The tables below compare two catalog factory loads in a steady 10 mph crosswind. They are simulator outputs for a controlled reference condition, not a substitute for measuring the conditions on your range.
What causes wind drift?
Drag acts against the bullet's velocity relative to the air. A crosswind changes that relative velocity, so drag gradually changes the bullet's horizontal velocity. The result is accumulated lateral displacement during time of flight. Wind is not simply a constant sideways force pushing on a bullet: the drag force and its direction change as velocity falls. A useful first approximation is drift ≈ crosswind speed × (time of flight − range ÷ muzzle velocity). The range uses the full drag integration rather than that approximation.
Full-value and half-value wind
A full-value wind crosses the line of fire at 90°. A half-value wind has about half that crossrange speed. In the table, angle is measured away from a full-value crosswind, so the crossrange component is wind speed × cos(angle). Wind from the opposite side reverses the direction of drift. A headwind or tailwind has no crossrange component, though it can slightly change time of flight.
| Angle | Crossrange fraction | 10 mph wind equivalent |
|---|---|---|
| 0° | 1.00 | 10.0 mph |
| 30° | 0.87 | 8.7 mph |
| 45° | 0.71 | 7.1 mph |
| 60° | 0.50 | 5.0 mph |
| 90° | 0.00 | 0.0 mph |
60° from full-value is a half-value wind; it is 30° from the line of fire.
Why ballistic coefficient matters
Ballistic coefficient (BC) describes how efficiently a projectile retains speed against a specified drag model. For these catalog loads, the 6.5 Creedmoor 140 gr ELD-M has a G7 BC of 0.326; the .308 Win 168 gr SMK has a G7 BC of 0.224. The higher-BC 6.5 projectile sheds speed more slowly, spends less time exposed to the same wind on its way to a distant target, and produces less wind drift in this comparison. BC must be compared within the same drag model;G1 and G7 values are not interchangeable.
.308 Win and 6.5 Creedmoor: 300–1000 yards
The WeaponTester range engine computed these values with a steady 10 mph, 90° wind at sea level: 59 °F, 29.92 inHg station pressure, 0% humidity, a 100-yard zero and 1.75-inch sight height. Loads are Federal Gold Medal Match .308 Win 168 gr SMK at 2650 fps and Hornady Match 6.5 Creedmoor 140 gr ELD-M at 2710 fps. Wind drift here is the difference between a windy and calm simulation, excluding spin drift. Inches are rounded to one decimal.
| Distance | .308 Win | 6.5 CM | Difference |
|---|---|---|---|
| 300 yd | 7.8 in | 5.0 in | 2.8 in |
| 400 yd | 14.5 in | 9.1 in | 5.3 in |
| 500 yd | 23.6 in | 14.6 in | 9.0 in |
| 600 yd | 35.6 in | 21.7 in | 13.9 in |
| 700 yd | 51.0 in | 30.4 in | 20.6 in |
| 800 yd | 70.3 in | 41.0 in | 29.3 in |
| 900 yd | 94.2 in | 53.6 in | 40.5 in |
| 1000 yd | 122.8 in | 68.5 in | 54.3 in |
Model estimates use catalog BC and advertised muzzle velocity. The .308 SMK approaches the transonic region before 1000 yd, so its last rows are more sensitive to load and conditions. The validation record checks trajectory drop against independent references; these wind figures are engine output, not separately measured field data.
Reading wind across the range
A single wind reading at the firing line does not describe the entire bullet path. Observe mirage through the optic for direction and changes, then compare it with vegetation, flags, or a wind indicator at several points downrange. Mirage can disappear in overcast light or appear flattened in strong wind; vegetation and flags respond differently by size and weight. Record the observed direction and variation instead of treating any one cue as an exact speed. If the wind changes during a test, recheck the inputs before comparing results.
Hold in the reticle or dial wind?
The range reports windage in both MOA and MIL for the selected load and conditions. A reticle hold keeps the wind turret at zero and makes changing the estimate quick. Dialing a stable correction moves the aiming reference to the center of the reticle, but a changed wind calls for a new setting. Use the unit printed on the optic's reticle and turret; see theMOA and MIL referencefor their angular relationship. The catalog'sViper PST Gen II with EBR-7C MRAD reticleis one example of a matching MIL reticle and turret system.
Test your current loadout
Open the range to change wind, distance, load and atmosphere, then compare the live drift and angular readouts with this reference table.
Open range →