⌖WEAPONTESTER
Optics fundamentals

How to dial a scope turret

Published: · 6 min read

A click is one indexed adjustment of a scope turret. Elevation moves the point of impact up or down; windage moves it left or right. Common precision turrets move ¼ MOA or 0.1 MIL per click. These are angular increments, so the same click covers more inches as distance increases. Check the marking on your own scope: increments and directions vary by model.

MOA per click vs MIL per click

One MOA spans about 1.047 inches at 100 yards; one MIL spans 3.6 inches. A ¼ MOA click therefore shifts impact about 0.262 inches at 100 yards, while a 0.1 MIL click shifts it 0.36 inches. The scales are different, but neither system is inherently more precise. Match the dope readout to the unit engraved on the turret. For the full conversion, see MOA vs MIL.

Worked example: .308 Win at 500 yards

Use a Federal Gold Medal Match .308 Win 168 gr Sierra MatchKing at its published 2650 fps from a 24-inch barrel. The projectile uses the catalog G7 BC of 0.224. With a confirmed 100-yard zero, 1.5-inch sight height, no wind and ICAO sea-level conditions (59 °F, 29.92 inHg station pressure, 0% humidity), the validated range engine puts the 500-yard impact 63.6 inches below the sight line. The required elevation is 12.14 MOA or 3.53 MIL up.

On a ¼ MOA turret, divide 12.14 by 0.25 and dial 49 clicks up (12.25 MOA). On a 0.1 MIL turret, divide 3.53 by 0.1 and dial 35 clicks up (3.5 MIL). A turret can only land on a whole click; that small rounding difference is normal. These values are a simulation reference, not a substitute for confirming your own rifle on paper or steel.

How to dial elevation and windage

  1. Confirm zero. Test on paper at your zero distance. Set both turret indices to zero only after confirming point of impact.
  2. Read dope. Enter the measured distance, load, muzzle velocity, atmosphere and wind. Read elevation and windage in the same unit as your turrets.
  3. Count clicks. Divide each correction by its turret increment, round to a whole click, and follow the turret’s marked direction. A rightward wind correction means moving impact right; check the scope’s marking, not the wind’s name.
  4. Test on target. Use a paper or steel target and observe the impact. If wind is changing, consider holding wind in a matched reticle instead of chasing it on the turret.
  5. Reconfirm. Record the actual correction, return elevation and windage to zero, and verify the zero again before the next test.

Elevation click comparison

Same reference load and conditions as above. Values are calculated from the engine’s drop at each distance and rounded to the nearest whole turret click. Windage is zero in this calm-air table; read a separate wind correction for actual conditions.

.308 Win elevation correction and MOA versus MIL turret clicks
RangeDropMOA up¼ MOA clicksMIL up0.1 MIL clicks
300 yd15.4 in4.92201.4314
500 yd63.6 in12.14493.5335
700 yd158.6 in21.63876.2963
1000 yd443.7 in42.3716912.32123

The 1000-yard result is beyond this load’s validated pre-transonic region; confirm it on target before relying on it.

Choosing a dialable optic

The catalog’s Vortex Viper PST Gen II 5–25x50 has exposed 0.1 MIL turrets with a zero stop, and the Leupold Mark 5HD 5–25x56 has a 0.1 MIL ZeroLock elevation dial. The catalog Strike Eagle 1–8x24 is a different setup: capped ½ MOA turrets, useful for zeroing but less convenient for frequent dialing. Nightforce NXS is another dialing-oriented scope family, but it is not in this catalog; check the exact model’s turret spec before using any click table. Compare elevation travel and turret units in the optics catalog, or shop dialable scopes through the catalog’s Viper PST listing.

Frequently asked questions

How many clicks do I dial for a 500-yard .308 shot?

For this Federal Gold Medal Match 168 gr SMK reference load at 2650 fps, 100-yard zero and ICAO sea level, the 500-yard correction is 12.14 MOA or 3.53 MIL. That rounds to 49 clicks on a 0.25 MOA turret or 35 clicks on a 0.1 MIL turret. Your own velocity, zero and atmosphere can change the solution.

What is the difference between MOA per click and MIL per click?

MOA and MIL are different angular units. A 0.25 MOA click is one quarter of a minute of angle; a 0.1 MIL click is one tenth of a milliradian. Read the increment engraved on your actual turret before converting a dope value to clicks.

Should I dial windage or hold for wind?

Either can work on a controlled range. Dial a stable, measured wind correction in the turret’s unit, or hold into the wind with a matching reticle. Variable wind is often easier to handle with a reticle hold. Recheck the wind and return the turret to zero afterward.

Sources and method

Test the correction

Dial it in the range

The preset opens a complete .308 Win 168 gr SMK build at 500 yards, a 100-yard zero and sea-level reference conditions. Check the dope readout, dial the optic, and test on steel.

Try this in the /range simulator →

Range essentials · Amazon affiliate links

Plan beyond the simulation

Compare personal protection and note-taking supplies for your next range visit.

Hearing protection

Compare earmuffs and earplugs by fit, comfort, and the manufacturer’s published protection rating.

Compare hearing protection on Amazon →

Eye protection

Compare safety glasses by coverage, lens tint, and documented impact rating.

Compare safety glasses on Amazon →

Keep your observations together

A weather-resistant notebook gives your session notes and conditions a home away from the screen.

Browse field notebooks on Amazon →

As an Amazon Associate, we earn from qualifying purchases. Links open Amazon search results; compare the current listings and specifications there. Affiliate disclosure