Scope Zero Distance
for Long Range
Last updated: · 10 min read
A scope zero is the range at which the line of sight (LOS) and the bullet's trajectory intersect. Because the bore sits below the optic and is angled slightly upward, every standard trajectory crosses the LOStwice, once on the way up (near-zero) and once on the way down (far-zero). When shooters say a rifle is "zeroed at 100 yards," they mean the far-zero is 100 yards. The zero distance you pick controls midrange rise, the size of holdover corrections at common engagement distances, and how cleanly your turret reads when you dial.
The geometry of a zero
Three lines define a zeroed rifle: the bore axis, the line of sight, and the bullet's curved trajectory under gravity. The bore points along a straight line. Gravity pulls the bullet below that bore line continuously. To compensate, the optic is mounted above the bore, most commonly 1.5 inches above the bore axis on a bolt-action precision rifle, or about 2.5 inches on an AR pattern, and the scope is dialed so the bore points slightly upward relative to the LOS.
That small upward tilt is what causes the two intersections. From the muzzle, the bullet starts below the LOS (by the sight-height distance), rises through it at the near-zero, continues climbing relative to LOS until trajectory apex, then drops back through LOS at the far-zero, and continues falling away. Past the far-zero, the bullet is always below the LOS. That's where you dial elevation or hold over.
Diagram derived from JBM trajectory output, .308 Win 168gr SMK (G7 0.218) at 2650 fps, standard ICAO atmosphere, 1.5" sight height, 200-yard zero. Vertical scale is exaggerated relative to horizontal for legibility; the actual rise is fractions of an MOA.
The 100-yard zero: universal reference
A 100-yard zero is the dominant precision-rifle convention for one reason: every elevation correction past 100 yards is a positive number dialed up on the turret. There is no midrange rise to mentally track, no negative correction for a closer-than-zero target, no ambiguity about whether your reticle's center is on or off the line of sight. This is why virtually every PRS competitor and most military and law-enforcement precision programs use it.
The tradeoff is that holdovers grow quickly. A .308 168gr SMK zeroed at 100 drops roughly 13 inches at 300 yards, 29 inches at 400, and 52 inches at 500, values you cannot hold accurately without a Christmas-tree reticle or a turret dial. If you are not going to dial, the 100-yard zero is the wrong choice past about 200 yards.
The 200-yard zero: hold-center for common ranges
A 200-yard zero shifts the entire trajectory up by enough that the bullet rides above LOS from roughly 40 yards to 200 yards, peaking near 120 yards at about 1.8 inches above point of aim for a typical .308 Win match load. Past 200, the bullet falls away at the same rate as a 100-yard zero, just from a higher reference point.
Practically, this means a single point of aim (centered on a 6- to 8-inch steel plate) covers muzzle out to roughly 235 yards without correction. Beyond that, you either dial or hold over. For a hunter or steel-target shooter who works mostly inside 250 yards and occasionally pushes to 400, the 200-yard zero reduces both the magnitude and the cognitive load of corrections.
The 300-yard zero: stretching the practical band
A 300-yard zero pushes the apex higher (about 5.4 inches above LOS at 200 yards for the same .308 load) and extends the no-holdover band further but at a cost of significant midrange rise. On a small target inside 200 yards, that 5-inch rise can push the round high enough to miss entirely. For shooters who consistently engage past 250 yards but want to avoid dialing for every shot, this zero earns its keep. For close-range steel, it does not.
Maximum point-blank range (MPBR)
MPBR formalizes the "what zero gives me the longest no-holdover band?" question. Given an acceptance window (the diameter of the target you want to keep the bullet inside, centered on the LOS), you solve for the zero distance that maximizes the range over which the bullet stays within ±window/2 inches of the LOS.
For an 8-inch acceptance window (a reasonable plate-target size) and a .308 Win 168gr SMK at 2650 fps with 1.5-inch sight height, the optimum is a zero of roughly 250 yards. The bullet rises about 3.5 inches above LOS at apex (near 145 yards), crosses LOS at 250, and falls 4 inches below LOS at roughly 295 yards. That gives an MPBR of about 295 yards: hold center, hit somewhere inside the plate, no correction needed.
A 6.5 Creedmoor 140gr ELD-M at 2710 fps under the same parameters extends MPBR to roughly 315 yards for the same 8-inch window, because the flatter trajectory rises more slowly and drops more slowly past the far-zero. MPBR is the practical-shooter's framework. The PRS or ELR shooter, who is always dialing, simply does not benefit from MPBR and is better served by a 100-yard zero.
Bullet path under each zero: .308 Win 168gr SMK at 2650 fps
Vertical impact relative to point of aim, in inches. Positive = above LOS, negative = below. JBM trajectory output, standard ICAO conditions, 1.5-inch sight height, no wind.
| Range | 100-yd zero | 200-yd zero | 300-yd zero |
|---|---|---|---|
| 100 yd | 0.0" | +1.9" | +4.4" |
| 200 yd | −3.8" | 0.0" | +5.4" |
| 300 yd | −13.4" | −8.2" | 0.0" |
| 400 yd | −29.1" | −22.6" | −12.3" |
| 500 yd | −52.3" | −44.5" | −32.0" |
| 600 yd | −84.0" | −75.2" | −60.0" |
Source: JBM Ballistics trajectory calculator, .308 Win 168gr Sierra MatchKing (G7 BC 0.218), MV 2650 fps, ICAO standard atmosphere, sight height 1.5". Values rounded to one decimal. Verify against your own load: MV variance of ±25 fps shifts the 600-yard column by several inches.
The same comparison for 6.5 Creedmoor 140gr ELD-M at 2710 fps
Higher G7 BC, slightly higher muzzle velocity, lower drag through the supersonic regime: every value in this table is smaller in magnitude than the .308 equivalent, especially past 400 yards. This is one of the structural reasons 6.5 CM dominates PRS and similar competitive disciplines.
| Range | 100-yd zero | 200-yd zero | 300-yd zero |
|---|---|---|---|
| 100 yd | 0.0" | +1.6" | +3.7" |
| 200 yd | −3.3" | 0.0" | +4.6" |
| 300 yd | −11.4" | −6.9" | 0.0" |
| 400 yd | −24.4" | −18.7" | −10.2" |
| 500 yd | −43.2" | −36.3" | −26.3" |
| 600 yd | −68.5" | −60.6" | −48.0" |
Source: JBM Ballistics, 6.5 Creedmoor 140gr Hornady ELD-M (G7 BC 0.315), MV 2710 fps, ICAO standard, sight height 1.5". Drop values are smaller in magnitude than the .308 table; every inch of advantage compounds as the bullet stays supersonic longer.
Turret style and zero choice interact
Your scope's turret style strongly influences which zero is rational. The two major patterns:
- Exposed, graduated turrets with zero stop: Nightforce NXS, Leupold Mark 5HD, Vortex Viper PST Gen II, Athlon Ares ETR, and similar. Designed for dialing. Pair with a 100-yard zero so every elevation correction past 100 is dialed up from the zero stop, and the turret reading directly matches the drop chart.
- Capped or BDC turrets: Vortex Strike Eagle, Leupold VX-5HD, hunting/tactical hybrids. Less suited to constant dialing. Pair with a 200- or 300-yard zero (or MPBR-optimized zero) and hold over for everything past the far-zero. A BDC reticle calibrated for your load makes the holdover read at common ranges.
First versus second focal planeis the other variable in this decision. Reticle holdovers only scale with target image on FFP optics, which is a non-negotiable for hold-over zeros at variable magnification.
A practical zeroing workflow
- Bore-sight first. Either through the bore on a bolt rifle, or using a laser bore sighter. Goal is to be on paper at 25 yards.
- Confirm at 25 or 50 yards. A round on paper at close range protects ammunition cost and rules out gross misalignment. A 25-yard impact point about 1.5 inches below LOS will roughly correspond to a 100-yard zero for a typical match load.
- Fine zero at the intended far-zero distance. Move to 100, 200, or whatever you've chosen. Fire a 5-round group from a stable rest. Adjust windage and elevation to bring the group center to the point of aim. Confirm with a second group.
- Set the zero stop (if present) on your elevation turret so dialed-down returns you cleanly to zero. Mark the windage turret zero with a paint pen or set its zero ring.
- Validate at a longer range. Compare actual drop at 300 or 500 yards to your ballistic calculator's prediction. If it disagrees by more than a quarter MOA, your input MV or BC is off, so chronograph your load and adjust the BC in your calculator until prediction matches truth at distance. This is true-ing the ballistic solver, and it is the single most important step.
Atmosphere affects everything past the zero
The numbers in the tables above assume ICAO standard atmosphere (59 °F, 29.92 inHg, sea level, 0% humidity). Air density changes the drop figures past the far-zero, but it does not change the zero distance itself in any meaningful way: the LOS-trajectory intersection at 100 or 200 yards is essentially fixed by geometry and only marginally affected by density.
Past 300 yards the gap opens. The same .308 load that drops 52 inches at 500 yards under sea-level standard atmosphere will drop closer to 47 inches at 5,000 feet elevation on a hot day. Seehow altitude, temperature, pressure, and humidity move the bulletfor the full treatment.
Setting your zero in the range tool
Therange simulatoraccepts your zero distance as an input alongside MV, BC, sight height, and atmospheric conditions. Try the three zeros covered here against the same target distance to see the vertical impact change in real time. The drop table updates the column it labels "from zero" based on the value you set.
In thebuilder, every optic in the catalog lists turret style (capped, exposed, locking) and reticle placement (FFP / SFP). If you know you'll be dialing, filter to exposed elevation turrets; if you'll be holding over, filter to FFP reticles with calibrated subtensions.
Frequently asked questions
What is the best zero distance for a long-range rifle?
For a dialing-style precision rifle, a 100-yard zero is the most common choice because it gives a clean reference point and every correction past that is dialed up on the turret. For shooters who hold over instead of dialing, a 200- or 300-yard zero reduces the magnitude of corrections at common engagement ranges. There is no universal best: the right zero depends on how you intend to make corrections, not on the cartridge.
Should I zero my .308 at 100 or 200 yards?
A 100-yard zero is the more flexible choice for a precision .308 Win because it pairs cleanly with dialed corrections: every adjustment past 100 yards is a positive elevation entry. A 200-yard zero produces a roughly 1.8-inch midrange rise and lets you hold center on an 8-inch steel plate from the muzzle out to about 235 yards without correction. Pick 100 if you dial, 200 if you primarily hold over.
What is MPBR (maximum point-blank range)?
MPBR is the longest distance over which the projectile path stays within an acceptance window (typically the diameter of the target) centered on the line of sight, requiring no holdover. For an 8-inch acceptance window with a .308 Win 168gr SMK at 2650 fps, the optimal MPBR zero is about 250 yards, producing an MPBR of roughly 295 yards. For 6.5 Creedmoor 140gr ELD-M at 2710 fps, the same window stretches MPBR to about 315 yards.
Does scope height above bore change the zero?
Yes. A taller sight height (AR pattern at 2.5 inches versus a bolt rifle at 1.5 inches) produces a steeper initial bore-to-LOS angle, which shifts the near-zero closer and changes the midrange trajectory rise. Always set the sight height input on your ballistic calculator accurately. JBM, Hornady, and the WeaponTester range tool all accept this as a parameter and produce noticeably different inside-100-yards behavior when it changes.
Does a 100-yard zero work at 1000 yards?
Yes, provided your scope has enough elevation travel. A typical 5-25x precision optic with 80-100 MOA of internal adjustment, combined with a 20 MOA canted base, will dial well past 1000 yards from a 100-yard zero on .308 Win or 6.5 Creedmoor. The 100-yard zero does not limit your maximum effective range, it just sets where the turret reads zero. Confirm your scope's total elevation travel against the predicted drop in MOA or MIL at your maximum intended range before committing.
Does temperature or altitude shift my zero?
The zero distance itself shifts only marginally: air density barely affects the bullet's path inside 200 yards. Past 300 yards, the gap between your zero atmosphere and your current conditions matters more, and you should validate your drop chart on-site rather than rely on stale numbers. Re-zero only if you have changed scope, mount, ammo lot, or notice a consistent group shift on paper at your zero distance.
Sources
- JBM Ballistics. Trajectory Calculator (Lite). jbmballistics.com. Industry-standard free trajectory tool, used to generate the .308 and 6.5 CM bullet-path tables above under standard ICAO conditions.
- Litz, B. Applied Ballistics for Long Range Shooting, 3rd ed. Applied Ballistics LLC, 2015. Source for measured G7 BCs of the 168gr SMK and 140gr ELD-M loads used in the examples.
- Hornady Mfg. Co. 140gr ELD Match Product Data Sheet. Source of the published G7 BC (0.315) and reference MV used in the 6.5 Creedmoor table.
- Sierra Bullets. 168gr MatchKing Reloading Data. Source of the published G1/G7 BC for the .308 Win reference load.
- NSSF / National Shooting Sports Foundation. Sighting In Your Rifle. Practical zeroing workflow and bore-sight procedure.
See your zero on the range
Build a .308 or 6.5 Creedmoor rifle, pick a scope from the catalog, and set zero distance in the range tool. Switch between 100, 200, and 300 yard zeros and watch the trajectory and drop table update.
Open the Builder →